UL PRODUCT CATEGORY

[Raceway] Surface Metal Raceway, RJBT


See General Information for Raceway

250.118(14)300.15(A)300.22(C)(1)322.30322.40324.10(D)368.56(A)(15)386.1386.100386.2386.6550.15(F)645.5(E)(2)250.118(14)300.15(A)300.22(C)(1)322.30322.40324.10(D)368.56(A)(15)386.1386.100386.2386.6550.15(F)645.5(E)(2)

USE

This category covers surface metal raceway intended for installation in accordance with Article 386 of ANSI/NFPA 70, "National Electrical Code" (NEC). This raceway is intended for installation and use in accordance with the following information.

GROUNDING

Surface metal raceway is considered suitable for grounding for use in circuits over and under 250 V and where installed in accordance with the NEC.

PRODUCT MARKINGS

The number, type and size of conductors which may be installed in the certified raceway is marked on the raceway, on the installation instruction sheet or on the package in which it is shipped.

Raceway for use with lighting fixtures and/or other devices is marked to this effect on the raceway or on the package in which it is shipped.

PRODUCT IDENTITY

One of the following product identities appears on the product:

    Surface Metal Raceway

    Surface Metal Raceway Base for Use with Labeled Raceway Cover

    Surface Metal Raceway Cover for Use with Labeled Raceway Base

RELATED PRODUCTS

Some luminaires covered under Fluorescent Surface-mounted Luminaires (IEUZ) are suitable for use as raceways.

ADDITIONAL INFORMATION

For additional information, see Electrical Equipment for Use in Ordinary Locations (AALZ).

REQUIREMENTS

The basic standard used to investigate products in this category is ANSI/UL 5, "Surface Metal Raceways and Fittings."

UL MARK

The Certification Mark of UL on the product or on the smallest unit container in which the product is packaged is the only method provided by UL to identify products manufactured under its Certification and Follow-Up Service. The Certification Mark for these products includes the UL symbol, the words "CERTIFIED" and "SAFETY," the geographic identifier(s), and a file number.

Alternate UL Mark

The Listing Mark of UL on the product or on the smallest unit container in which the product is packaged is the only method provided by UL to identify products manufactured under its Listing and Follow-Up Service. The Listing Mark for these products includes the UL symbol (as illustrated in the Introduction of this Directory) together with the word "LISTED," a control number, and the product name "Surface Metal Raceway," "Surface Metal Raceway Base for Use with Labeled Raceway Cover" or "Surface Metal Raceway Cover for Use with Labeled Raceway Base."

* * * * * * * * * * * * * * * * * * * * * * * * *

UL, in performing its functions in accordance with its objectives, does not assume or undertake to discharge any responsibility of the manufacturer or any other party. UL shall not incur any obligation or liability for any loss, expense or damages, including incidental or consequential damages, arising out of or in connection with the use, interpretation of, or reliance upon this Guide Information.

Box ConnectorsRaceway, Surface MetalRaceway Bases, Surface MetalRaceway Covers, Surface MetalSurface Metal Raceway BasesSurface Metal Raceway Covers
Last Updated on 2013-05-16
RJBT.GuideInfo RJBT Active 20130516 20110727

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "© 2019 UL LLC".