UL PRODUCT CATEGORY

Heating, Cooling, Ventilating and Cooking Equipment, AAHC


GENERAL

This equipment is intended for heating, cooling, refrigerating, ventilating and cooking, and uses various energy sources including electricity, gas, petroleum-base liquid, solid fuel or solar energy.

Fuel-fired equipment is intended for use only with the fuels described in the general Guide Information for each product category and individual certifications. This equipment has been investigated for use as described in the instructions and markings provided with the equipment. The use of the equipment with other fuels, and in conditions other than described in the instructions, markings and the general Guide Information for the applicable product category, has not been investigated by UL.

INVESTIGATION REQUIREMENTS AND STANDARDS

The scope of product sizes and ratings appearing in the general Guide Information for some product categories is intended to indicate the current range of certified products, however, it is not necessarily indicative of limitations for those certified products.

The standards used to investigate products are identified in the general Guide Information for each product category. There may not always be a published standard for investigating a product to determine its acceptability for certification. If no applicable standard is available, UL will exercise its judgment in the selection of applicable requirements from related standards and other sources to develop the requirements to cover uses and conditions for which specific requirements did not previously exist.

Products, equipment and construction materials certified by UL in accordance with international or regional standards only (e.g., products certified to an IEC or ISO standard) are intended for distribution, installation and use in areas of the world where the specified standards have been adopted and are in effect as national or regional standards.

INSTALLATION REQUIREMENTS

The limitations for the equipment as specified in the general Guide Information for each product category such as voltage and temperature limits, markings, special descriptions and installation provisions need to be noted prior to installation and use.

Equipment has been investigated with reference to risks to life and property and for conformity to the installation and use provisions of the applicable installation codes and standards of the National Fire Protection Association (NFPA), and applicable model codes identified in the general Guide Information for each product category.

In addition, certain products have been investigated with reference to environmental and public health effects and for conformity to the installation and use provisions of applicable environmental and public health requirements, if so indicated in the general Guide Information for each product category.

Some products are certified for uses not within the scope of nationally recognized installation codes and standards. Such products are investigated for the specifications or use conditions indicated in the general Guide Information for each product category.

These products are intended for installation subject to approval by the Authority Having Jurisdiction. Authorities Having Jurisdiction should be consulted before installation.

INSTRUCTIONS AND PRODUCT MARKINGS

These products are intended to be installed in accordance with the installation instructions provided with the product. It is critical that the cautionary statements and installation and operating instructions on the product and in accompanying literature be followed.

INDOOR AND OUTDOOR USE

Unless outdoor use is specifically indicated in the general Guide Information for the product category or included in the individual certifications of the product, individual appliances have been investigated only for use indoors, unless the product, by its inherent nature, is obviously intended for use outdoors.

ELECTRICAL INSTALLATIONS

General — The ampere or wattage marking on electrical power-consuming equipment is valid only when the equipment is supplied at its marked rated voltage. In general, the current input to electric heating appliances or resistance heating equipment will increase in direct proportion to an increase in the supply voltage, while the current input to an induction motor supplying a constant load will increase approximately in direct proportion to a decrease in the supply voltage. These increases in current can cause overcurrent protection devices to open even when these devices are properly selected on the basis of nameplate ratings.

Supply Conductors — Except as noted in the general Guide Information for some product categories, terminals are for use only with copper wire unless marked otherwise. If aluminum or copper-clad aluminum wire can be used, marking to indicate this fact is provided. Such marking is required to be independent of any marking on terminal connectors, such as on a wiring diagram or other visible location. The marking may be in an abbreviated form, such as "AL-CU."

Except as noted below or in the general Guide Information for certain product categories, the electrical termination provisions on equipment are based on the use of 60°C insulated conductors in circuits rated 100 A or less and the use of 75°C insulated conductors in higher rated circuits. Termination provisions are determined based on values provided in Table 310.15(B)(16) with no adjustment made for correction factors.

If the electrical termination provisions on equipment are based on the use of other conductors, the equipment is either marked with both the size and temperature rating of the conductors to be used or with only the temperature rating of the conductors to be used. If the equipment is only marked for use with conductors having a higher (75 or 90°C) temperature rating (wire size not specified), the 60°C ampacities (for circuits rated 100 A or less) and 75°C ampacities (for circuits rated over 100 A) specified in Table 310.15(B)(16) of ANSI/NFPA 70, "National Electrical Code" (NEC), should be used to determine wire size. Conductors having a temperature rating higher than specified may be used, though not required, if the size of the conductors is determined on the basis of the 60°C ampacity (circuits rated 100 A or less) or 75°C ampacity (circuits rated over 100 A).

Copper-clad aluminum conductors are subject to the ampacity requirements applicable to aluminum conductors.

Terminations — Copper pigtail leads may be used with aluminum or copper-clad aluminum supply wires in dry locations if 1) the splicing devices are certified for use in joining copper to aluminum, 2) there is sufficient wiring space, and 3) the means provided for connecting the wiring system are acceptable for the wire size used.

Supply terminals of 15 A and 20 A switches and receptacles not marked "CO/ALR" are for use with copper and copper-clad aluminum conductors only. Terminals marked "CO/ALR" are for use with aluminum, copper and copper-clad aluminum conductors.

Screwless terminal connectors of the conductor push-in type (also known as push-in terminals) are restricted to 15 A branch circuits and are for connection with 14 AWG solid conductors only. They are not intended for use with aluminum or copper-clad aluminum conductors, 14 AWG stranded copper conductors, or 12 AWG solid or stranded copper conductors.

Terminals of switches and receptacles rated 30 A and above not marked "AL/CU" are for use with copper conductors only. Terminals of switches rated 30 A and above marked "AL/CU" are for use with aluminum, copper and copper-clad aluminum conductors.

Combination of dissimilar conductors in terminal or splicing connectors is acceptable only in dry locations and when the connectors are identified as suitable for such intermixing.

Hazardous Locations — Electrical equipment and appliances are not intended for use in hazardous (classified) locations, as defined in the NEC, unless specifically identified as suitable for use in hazardous locations.

FIELD-MODIFIED OR REBUILT EQUIPMENT

An authorized use of the UL Mark is the manufacturer's declaration that a product was manufactured in accordance with the applicable certification requirements, and was in compliance with those requirements when it was shipped from the factory. When a product bearing a UL Mark is modified or rebuilt (including being refurbished, remanufactured, reconditioned or renovated) after it leaves the factory where the UL Mark was applied, UL does not know if the product continues to meet the applicable requirements unless the modification or rebuilding has been specifically investigated by UL. The only exceptions to this are when a UL-certified product has specific markings for field-installed equipment or the replacement of components, or when the individual product is addressed through one of the specific programs noted below.

Evidence that UL has specifically investigated the modification or rebuilding can only be demonstrated by a product that bears the UL Mark or label of one of UL's programs for modified or rebuilt equipment, which include:

UL Rebuilt Product Certifications — UL's rebuilt product certifications cover a wide range of product types. The general Guide Information for each product category with a rebuilt certification program identifies the applicable requirements and the specific marking for products rebuilt under the program. Only rebuilt products that bear the UL Mark together with the word "Rebuilt," "Refurbished," "Remanufactured," "Reconditioned" or "Renovated" have been investigated by UL to the applicable certification requirements.
UL Retrofit Certifications — UL's retrofit certifications include an investigation of all required component parts, including instructions, for retrofitting specific types of certified products in the field. Products investigated under this program bear a UL Mark together with the product identity including the word "Retrofit."
UL Field Evaluated Products — For products identified by the Authority Having Jurisdiction, owner, or other regulatory body as being acceptable to evaluate after installation or otherwise outside of the manufacturer's location, UL's Field Evaluation program addresses investigation to applicable product requirements based on the specific application and use location for the particular equipment. The specific equipment investigated under this program bears the UL Field Evaluation label.

* * * * * * * * * * * * * * * * * * * * * * * * *

UL, in performing its functions in accordance with its objectives, does not assume or undertake to discharge any responsibility of the manufacturer or any other party. UL shall not incur any obligation or liability for any loss, expense or damages, including incidental or consequential damages, arising out of or in connection with the use, interpretation of, or reliance upon this Guide Information.

Last Updated on 2017-09-11
AAHC.GuideInfo AAHC Active 20170911 20170911

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "© 2019 UL LLC".