Fire-resistance Ratings Certified for Canada, BXRH7


Fire-resistance ratings are included for:

1. Assemblies, such as beams, floors, roofs, columns, walls and partitions. These fire-resistance designs provide the detailed construction of the assemblies and the components used.
2. Systems, such as construction joint systems, through-penetration firestop systems, electrical circuit protective systems and duct assemblies. These designs provide the detailed construction of the systems and the components used.
3. Opening protectives, such as dampers, fire doors, glazing and related equipment. Opening protectives are used to protect openings in fire-resistance-rated assemblies.

These materials are intended for use only in specific assembly or system designs as described in the general Guide Information for each product category and individual certifications, except for opening protectives. Opening protectives have been investigated for use as described in the instructions and markings provided with the opening protectives. The use of the materials and opening protectives in conditions other than described in the instructions, markings and the general Guide Information for the applicable product category has not been investigated by UL.


The scope of product sizes and ratings appearing in the general Guide Information for some product categories is intended to indicate the current range of certified products, however, it is not necessarily indicative of limitations for those certified products.

The standards used to investigate products are identified in the general Guide Information for each product category. There may not always be a published standard for investigating a product to determine its acceptability for certification. If no applicable standard is available, UL will exercise its judgment in the selection of applicable requirements from related standards and other sources to develop the requirements to cover uses and conditions for which specific requirements did not previously exist.

Products, equipment and construction materials certified by UL in accordance with international or regional standards only (e.g., products certified to an IEC or ISO standard) are intended for distribution, installation and use in areas of the world where the specified standards have been adopted and are in effect as national or regional standards.


The limitations for the equipment as specified in the general Guide Information for each product category such as voltage and temperature limits, markings, special descriptions and installation provisions need to be noted prior to installation and use.

Equipment has been investigated with reference to risks to life and property and for conformity to the installation and use provisions of the applicable installation codes and standards developed by the Canadian Commission on Building Codes and Fire Codes (CCBFC), CAN/CSA-C22.1, "Canadian Electrical Code, Part I" ("CE Code"), and the applicable model codes identified in the general Guide Information for each product category.

Some products are certified for uses not within the scope of nationally recognized installation codes and standards. Such products are investigated for the specifications or use conditions indicated in the general Guide Information for each product category.

These products are intended for installation subject to approval by the Authority Having Jurisdiction. Authorities Having Jurisdiction should be consulted before installation.


These products are intended to be installed in accordance with the installation instructions provided with the product. It is critical that the cautionary statements and installation and operating instructions on the product and in accompanying literature be followed.


An authorized use of the UL Mark is the manufacturer's declaration that a product was manufactured in accordance with the applicable certification requirements, and was in compliance with those requirements when it was shipped from the factory. When a product bearing a UL Mark is modified or rebuilt (including being refurbished, remanufactured, reconditioned or renovated) after it leaves the factory where the UL Mark was applied, UL does not know if the product continues to meet the applicable requirements unless the modification or rebuilding has been specifically investigated by UL. The only exceptions to this are when a UL-certified product has specific markings for field-installed equipment or the replacement of components, or when the individual product is addressed through one of the specific programs noted below.

Evidence that UL has specifically investigated the modification or rebuilding can only be demonstrated by a product that bears the UL Mark or label of one of UL's programs for modified or rebuilt equipment, which include:

UL Rebuilt Product Certifications — UL's rebuilt product certifications cover a wide range of product types. The general Guide Information for each product category with a rebuilt certification program identifies the applicable requirements and the specific marking for products rebuilt under the program. Only rebuilt products that bear the UL Mark together with the word "Rebuilt," "Refurbished," "Remanufactured," "Reconditioned" or "Renovated" have been investigated by UL to the applicable certification requirements.
UL Retrofit Certifications — UL's retrofit certifications include an investigation of all required component parts, including instructions, for retrofitting specific types of certified products in the field. Products investigated under this program bear a UL Mark together with the product identity including the word "Retrofit."
UL Field Evaluated Products — For products identified by the Authority Having Jurisdiction, owner, or other regulatory body as being acceptable to evaluate after installation or otherwise outside of the manufacturer's location, UL's Field Evaluation program addresses investigation to applicable product requirements based on the specific application and use location for the particular equipment. The specific equipment investigated under this program bears the UL Field Evaluation label.


Fire-resistance assemblies and products are developed by the design submitter and have been investigated by UL for compliance with applicable requirements. The published information cannot always address every construction nuance encountered in the field.

Design Modifications

Careful consideration needs to be given to alterations or modifications of the fire-resistance assemblies.

When field issues arise, it is recommended the first contact for assistance be the technical service staff provided by the product manufacturer noted for the design. Users of fire-resistance assemblies are advised to consult the general Guide Information for each product category and each group of assemblies. The Guide Information includes specifics concerning alternate materials and alternate methods of construction.

Contacting UL

UL provides assistance to users of fire-resistance assemblies and products, which includes clarification of the published information.

UL also provides a service to investigate modifications to the fire-resistance assemblies when requested by the design submitter. Requests for clarification should describe the change and include drawings, if necessary.

Requests for clarifications or investigations can be made by contacting UL at:

* * * * * * * * * * * * * * * * * * * * * * * * *

UL, in performing its functions in accordance with its objectives, does not assume or undertake to discharge any responsibility of the manufacturer or any other party. UL shall not incur any obligation or liability for any loss, expense or damages, including incidental or consequential damages, arising out of or in connection with the use, interpretation of, or reliance upon this Guide Information.

Last Updated on 2017-09-11
BXRH7.GuideInfo BXRH7 Active 20170911 20170911

The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "© 2019 UL LLC".